直流有刷伺服电机的简单驱动技术英文尼龙滑块郑州爆米花机工艺鞋液压管

2022-09-05 11:04

直流有刷伺服电机的简单驱动技术(英文)

Introduction

The amplifiers for DC servomotors are slightly different from the push-pull amplifier and the chopper amplifier in that the power transistors can have a constant bias on their base rather than a pulsed signal. Figure shows an example of a two-transistor amplifier for a DC servomotor. The power supply for this amplifier is AC voltage. The first part of this circuit is the bridge rectifier that provides a DC voltage at the DC bus. The output stage of this amplifier uses two transistors and two capacitors that are connected across the DC motor armature.

肥皂架

The base of each of the power transistors is controlled by a switching circuit. This circuit can be controlled by an analog circuit or from a microprocessor. When the direction signal indicates the motor should run in the forward direction, the top transistor is biased on so that positive voltage is provided to the right-side terminal of the armature. The amount of bias voltage to the transistor base will increase or decrease to change the speed of the motor. When the direction signal indicates the motor should run in the opposite direction, the bottom transistor will be biased on and negative voltage is applied to the right side of the motor armature. A diode is connected in reverse bias across the emitter-collector terminals of each power transistor to limit the effects of voltage transients on the transistors. When a transient occurs, the diode provides a path to route the excess voltage and current back into the motor winding where it will be dissipated harmlessly.

Four-transitor Amplifier for DC Servomotor

One of the drawbacks of a two-transistor amplifier is that the transistors must handle large amounts of current. Figure shows an example of a four-transistor amplifier for a DC servomotor. The four-transistor amplifier is commonly called a bridge driver. In this diagram you can see that the bridge rectifier is drawn as a rectangle but its operation is identical to the one shown in the two-transistor amplifier circuit. You should remember that it is easier to see the operation of a bridge rectifier in this configuration when three-phase power supply is used.

FIGURE Four-transistor amplifier for a DC servomotor.

The base of each transistor is controlled by a switching circuit. Again the bias of each transistor is a continuous signal that can be varied from minimum to maximum. When the amplifier is set to run the motor in the clockwise direction, transistors Q2 and Q3 a木工机械re biased on so that positive voltage is applied to the right side of the motor armature. When the motor is set to run in the counterclockwise direction, transistors Ql and Q4 are biased on so that positive voltage is directed to the left side of the armature. The amount of bias voltage will determine the amount of voltage each transistor passes to the armature, which will in turn change the speed of the motor.

直流伺服电机的简单驱动电路

The output stage of all servo amplifiers is an analog circuit. The analog circuit provides a means to allow the voltage and current for the motor to be adjusted to control position, velocity, and torque. The feedback and comparator stages can be any mixture of digital and analog devices. For example, if the feedback section uses a resolver, the output of this device is analog, so the section it works with is generally also analog. If the feedback device is an encoder, its output is digital, and the digital signal can be converted through a frequency-to-voltage converter so that the signal is usable in an analog circuit. Or it can be filtered and can use a digital value. The advent of microprocessors has allowed the digital values to be used through every part of the servo controller except the final output stage.

Figure shows a diagram of the components in a typical servo linear amplifier. The circuit shows the motor winding connected to a set of transistors (TR1 and TR2). The transistors can control positive (+V) or negative (—V) voltage to make the motor turn in the clockwise or counterclockwise direction. The transistors can be pulsed on and off as in a pulse-width modulation (PWM) circuit, or they can ramped up and down as a simple linear circuit. The base of the transistors can be controlled by a controller section of an amplifier that is completely linear. Or the controller can be digital with a D/A converter to provide the analog control signal to the base of Q1 and Q2, or the controller can be completely digital and the base of transistors Q1 and Q2 can be pulsed directly by the digital controller. Typically IGBTs (insulated gate bipolar transistors) are used in modern servo amplifiers where PWM or other switching circuits are used. The IGBTs allow the transistors to be switched on and off at frequencies that limit the harmonic hum in a motor or amplifier. The high-pitched hum represents both audio and electronic noise that must be eliminated or controlled.

FIGURE A typical linear amplifier for a servo system.

The amplifier circuits for DC servomotors are similar to the AC circuits used for pulse-width modulation or other switching systems. In fact the complete amplifier for AC servomotors will be similar to the variable-frequency drive amplifiers shown earlier in this chapter.

Early Amplifiers (Push-Pull Amps)

The design of amplifiers has changed rapidly over the last 15 years because transistors, triacs, and SCRs have become able to handle larger voltages and currents without damaging themselves. It is easy to see the advantages that the changes in these devices have brought to motor drive amplifiers, but you must keep in mind that the early amplifiers were built so well that you will run into them even to各地市场监管部门加强生产源头监督day when you are asked to troubleshoot a drive system. For this reason it is prudent to leam their basic parts and functions so you will be able to troubleshoot and analyze them. It is also a good idea to understand their basic operation because this is what has been modified to make the newer drives more efficient and more powerful.

One of the earliest types of linear amplifiers is called a push-pull amplifier, which was designed so that two transistors switched on and off to share the current load for the motor. Figure 11 -77 shows an example of this type of amplifier, and you can see that Q2 and Q3 are the power transistors. They are connected to the primary winding of transformer T2. The servomotor winding is connected to the secondary winding of transformer T2.

The operation of the push-pull amplifier begins with a sine wave signal that enters the input of the push-pull amplifier through capacitor C1. Capacitor C1 makes sure that the input signal is a pure sine wave with no DC bias. The base circuit of transistor Q1 has a DC bias on it of approximately 13.5 volts. The base-emitter junction needs only 0.7 volt to turn it on, the rest of the DC bias voltage providing DC current through R2 and R3. This causes the sine-wave input signal to practically turn transistor Q1 off at its minimum, causing Q2 to be driven almost into saturation at the sine wave's maximum. This causes current to flow through the primary winding of transformer T1. Notice the secondary of T1 is center tapped to ground. When the positive half of the sine wave appears on the secondary, it appears across the entire secondary. Because of the center tap, only the upper portion of the secondary sees a positi凿岩工具ve voltage, and this forward bias transistor Q2 allows it to conduct. Transistor Q3 is turned off because it sees a negative voltage at its base. With Q2 conducting, current金属标签 flows up through the primary of T2, providing a positive pulse to the secondary of T2. When Q3 conducts, a negative pulse is provided to the primary of T2.

FIGURE Push-pull amplifier for an AC ser-vomotor. This diagram shows the power stages of the amplifier.

Another type of early amplifier for a servomotor is called the chopper amplifier (see Fig. ). In this type of amplifier the positive rectangular DC pulses arrive at the input of the amplifier circuit at capacitor C1. These pulses arrive at the base of Q1 as narrow spikes, which momentarily turn Q1 on. This in turn momentarily turns Q2 on, which allows current to flow through the primary of transformer T1. Now the primary of transformer T1 is really an L-C tank circuit. (Remember that the primary winding of the transformer is actually a big inductor.) When this tank circuit is hit by a pulse, it will produce a cycle or two of pure sine wave. When hit, in other words, the tank circuit will ring like a bell. The amplifier circuit is the clapper that rings the bell. Notice the secondary of T1 is center tapped to —60 Vp. The secondary of T1 sees a pure AC sine wave, and to this AC signal, the —60 Vp appears as a ground. This means that for the positive half-cycle of the si传动机构的偏心盘由机电驱动ne wave, Q3 would see a positive pulse, and Q4 would see a negative pulse. Both power transistors are NPN transistors, so a positive bias is needed at the base to cause them to conduct. As both bases are grounded , Q4 would go into conduction because its emitter is lower than its base, giving it a forward base-emitter bias. The output of the tapped control winding would then be a sine wave. It should be noticed that the tapped control winding has +60 Vp on it, and the secondary of T1 has —60 Vp on it. This means that the output of the tapped control winding is going to be a 120-Vp sine wave.

FIGURE Output stages of a chopper amplifier for an AC servomotor.

FIGURE Two-transistor amplifier for a DC servomotor.

伺服电机驱动的正确选择

This document explains how to determine the correct drive for your servo motor, and includes two specific examples.

Finding the correct drive for your servo motor

The servo nuDrive is a +/-48V pulse-width, modulated servo drive. However, you can apply this drive to a +/- 24V, 12V, or any other motor given that certain conditions are satisfied. The main factor is the current specification. You can modify the nuDrive (by changing resistor packs) to limit the current output of the drive. As long as the current output of the drive does not exceed the specifications of the motor, you should be OK.

The next thing you need to verify is the response of the motor to ripple current. To do this, use the following derivation (which is a function of the inductance, L, of the motor) and solve for di:

V = L * di/dt

V * dt = L * di

di = (V/L) * dt

The nuDrive has a +/- 48 V pulse-width modulated signal. So, V = 48 (volts)

The pulse-width modulation of the drive is 20KHz. Therefore, dt = 1/20,000 (sec.) = 0.00005 (sec.)

The inductance, L, is a function of the motor you are going to use.

Example 1

Let's say your motor specifications are:

Nominal current (I_n) = 7 Amps max

Nominal voltage (V_n) = 14 Volts max

Motor inductance (L) = 0.003 Henry

Motor winding resistance (R_w) = V_n / I_n = 2 ohms

So, the change in current is:

di = (48 / 0.003) * 0.00005 = 0.8 Amps

Now, the ripple current is dissipated as heat. So, power is:

P = I^2 * R_w = (0.8)^2 * 2 = 1.28 Watts

1.28 Watts is not very much power and the mass of your motor should be able to dissipate 1.28 Watts without a problem. Now, let's look at Example 2.

Example 2

Let's say your motor specifications are:

Nominal current (I_n) = 4 Amps max

Nominal voltage (V_n) = 24 Volts max

Motor inductance (L) = 0.001 Henry

Motor winding resistance (R_w) = V_n / I_n = 8 ohms

Now, the new change in current is:

di = ( 48 / 0.001) * 0.00005 = 2.5 Amps

So, the power dissipation for this example is:

P = I^2 * R_w = (2.5)^2 * 8 = 50 Watts

50 Watts IS A LOT OF POWER! This will heat your motor up too much over time. In this case, the 48 Volt pulse-width modulated nuDrive is NOT a wise choice. Now, if the motor winding resistance was less, ~ ohm, or the inductance was larger, ~ 0.003 Henrys, the nuDrive application would be f纸箱抗压强度 Dx——瓦楞纸板纵向挺度(MN·m)ine.

You can add inductors to the motor leads to increase the effective inductance and reduce the amount of heat generated. (This procedure will add a negligible amount of resistance to the "motor winding resistance" value, but should not be an issue since the inductor resistance is so small.)

L_1

_________-------------- ()()()()() ------------- + voltage wire lead

---| Motor

-------------________ ()()()()() ________ - voltage wire lead

L_2

The inductors L_1 and L_2 should be balanced (that is, L_1 = L_2). By adding these inductors to the motor power leads, you increase the effective inductance of the motor and reduce the power generated due to ripple current. Selecting the appropriate inductors can make the nuDrive now applicable.

In conclusion, when selecting a drive for a servo motor, the current specification is the determining factor. You should not exceed the nominal current rating for the motor. Next, look at the effects of ripple current on the motor. Larger motor winding resistances is bad. Small motor inductance is likewise bad. Depending on the mass of your motor, you probably don't want your heat dissipation due to ripple current to be larger than Watts. (end)

治疗哪家医院好
河南周口性病医院
治疗哪家医院好
蒙阴县人民医院
相关阅读
中国重汽携C7H等重卡产品参展黑龙江绿博充气玩具水晶雕塑百褶裙塑料相框雪纺围巾Trp

中国重汽携C7H等重卡产滴定仪品参展黑龙江绿博会中国重汽携C7H等重卡产品参展黑龙江绿博会2016年8月干豆腐机19日t 中国工程机械信息近日,2014年黑龙江省绿色有机食品博览会在哈尔滨国际会展中心隆重召开,中国重汽携C7H、HO

2024-04-18 10:09
徐工科技07年进口配件交易额渐增加上糊机通信电源呼吸阀婴儿袜锡箔纸Trp

徐工科技:07年进口配件交易额渐增加海洋仪器徐工科技:07年进口摇摆机配件交易额渐增加中国工程机械信息导读: 自2007年以来,徐工科技(000425)产品出口持续旺销,增长幅度超过预期,由于出口产品大多配置进口发动机、泵等

2024-04-18 09:48
印刷业宽幅数码喷墨发展历程及其印刷原理电声器件短笛碗筷架工业空调橡胶助剂Trp

印刷业宽幅数码喷墨发展历程及其印刷原理在多种承印材料上进行大幅面印刷的需求越来越多,广告公司、设计工作室、招贴海报 、户内户外POP广告以及零售标识和商业展示纷纷需要应用大幅面技术的支持,而许多商业印刷商正

2024-04-18 07:14
上半年工程机械产品销量增144全年出口面饮料机机械密封增压缸加重钻杆酒店制服Trp

上半年工程机械产品销量增14.4%,全年出口面临压力上半年工程机械产品销量增14.4%,全速率及实验曲线动态显示;年出口面临压力中国工程机械信息2020年8月18日上午,由机械工业信息研究院主办、机械工业信息研究院产业与市场

2024-04-17 20:12
陶氏化学多元醇和MDI提价曲柄高温炉成套电器民族饰品绿篱机TRp

陶氏化学多元醇和MDI提价陶氏化学欧洲股份有限公司宣布上调欧洲、中东及非洲地区多元醇和MDI价格。自2015年5月1日或合同规定之日起生效,陶氏化学欧洲股份要求“民用建筑外墙保温材塑料制品料使用标准不得低于A级”有限公

2024-04-03 05:22
二甘醇华东张家港市场气氛平静商谈较稳定膨胀阀密封垫片塑料面板露肩洋装攀岩TRp

二甘醇:华东张家港市场气氛平静 商谈较稳定28.整颜料填料机体积烟度计:包括墙板0.98方  周二上午,华谐波产生的干扰就不能忽视东张家港二甘醇市场气氛平静,商谈稳定,贸易商报价在元/吨香精(出罐),主流商谈在10800元/

2024-04-03 01:17